Hypertec Network Card HYNEP61001 User Manual

HyperNet  
PCMCIA 10/100 TX  
HYNEP61001  
USER GUIDE  
Information in this document is subject to change without notice. All rights reserved. All brand names are  
registered trademarks of their respective companies.  
 
INTRODUCTION  
Overview  
The HyperNet PCMCIA 10/100 TX network interface card is a dual speed (10/100) high performance PC Card that allows PCMCIA equipped  
portable computer users to enjoy high throughput in both, the existing legacy 10Mbps (10BASE-T) and newer100Mbps (100BASE-TX) Ethernet  
networks.  
The HyperNet PCMCIA 10/100 TX supports a wide selection of network operating systems, including Window NT, Windows 98, Windows 95,  
Windows 3.x and more.  
With the software drivers provided you can use the PCMCIA card with current operating systems which do not yet support PCMCIA technology.  
Features  
Automatic sensing and switching between 10Mbps and 100Mbps operation  
Full Duplex capabilities - Independent receive and transmit circuits allow for full duplex operation at both 10Mbps and 100Mbps, giving the  
PC Card a maximum throughput of 200Mbps  
A Single RJ-45 female connector supports both 10Mbps and 100Mbps operation  
Direct Enablers to reduce memory requirements included  
Supports all major Network Operating Systems, including Windows 98, Windows 95, Windows NT, Novell NetWare  
Superior Ethernet throughput performance using dynamic pipelining technology  
 
INSTALLATION  
Checklist  
Your package should contain the following items:  
One HyperNet PCMCIA 10/100 TX Card  
One 3.5" driver disk  
One media coupler cable  
If you do not have each of these items, contact your supplier before proceeding further.  
Static Electricity Warning  
Static electricity is accumulated naturally in the human body, and can be discharged through electrical components by touching them. This shock  
can potentially cause permanent internal damage to the component.  
When installing the adapter, please observe the following precautions:  
Discharge yourself before commencing by touching a grounded metal appliance, such as the metal frame of a computer - while it is tuned off, but  
still plugged into the wall socket.  
Hold the adapter or any other boards by their edges only. Never touch any exposed pins on the adapter.  
If possible, install the adapter as soon as you remove it from its anti-static bag, without putting it down. If you must put it down, place it on the  
anti-static bag in which it was packed.  
Do not place the adapter on any metal surface.  
 
Hardware Installation  
The HyperNet PCMCIA 10/100 TX hardware installation is a three step process:  
1. Insert the HyperNet adapter into the computers PCMCIA slot  
2. Connect the media coupler to the HyperNet adapter  
3. Attach the network cable  
The HyperNet PCMCIA 10/100 TX adapter is a Type 11 PC Card which is compatible with any Type 11 PCMCIA slot. If your computer has  
more than one slot, you may insert the adapter in any of them. The software will automatically determine into which slot the adapter is inserted.  
Gently insert the card into the PCMCIA slot, pushing until it sits firmly in place, care must be taken not to force it as the adapter is 'keyed' to fit  
only one way. If it does not register smoothly, withdraw it and check that the keyed plug on the adapter is correctly aligned with the keyed socket  
in the host PC.  
Now attach the media coupler to the 15-pin keyed socket on the exposed end of the adapter. This media coupler will have an RJ45 female  
connector that supports both 10Mbps and 100Mbps networks, insert your RJ45 cable into this connector on the coupler, and insert the other end  
to the wall socket or Ethernet hub.  
Windows Installation for Set-Up Guide  
To install the HyperNet PCMCIA 10/100 TX using Windows, follow the instructions on the Online User Guide once installed as below:  
1 Start Windows.  
2 Insert the HyperNet software disk into the PC disk drive.  
3 From the Program Manager, select File Menu.  
(For Windows 95, select the start menu)  
4 Select Run…  
5 Type A:\SETUP and select OK.  
6 Follow the Help utility's on-screen instructions for the setup process.  
DOS Installation  
Look at the README file.  
Software Included  
ODI workstation drivers for Novell NetWare, NetWare Lite, and Novell DOS 7  
NDIS 2.0.1 driver for Microsoft LAN Manager, Windows for Workgroups, Artisoft LANtastic  
NDIS 3 for Windows 98, Windows 95 and Windows NT  
Wizard utility for installation, self-test and diagnostics  
Disconnecting the HyperNet PCMCIA 10/100 TX  
Please ensure that the operating system allows you to remove the card while the system is running before trying to do so, if in doubt then shut  
down you computer before removing the adapter.  
To remove the card from the computer PCMCIA slot, activate the release switch located on your computer. Alternatively, you may simply  
disconnect the media coupler, and leave the HyperNet Card in place in the slot ready for you to use it next time you need it.  
To remove the media coupler from the card, gently squeeze the plastic clip depressors located on the coupler and separate it from the card.  
Never disconnect the HyperNet Card by pulling on the cable.  
If at any time during installation you experience difficulties, please contact Hypertec Technical Support on +44 1488 686844 (01488 686844 in  
the UK).  
 
SPECIFICATIONS  
Interface Standard:  
Type II PCMCIA PC Card  
PCMCIA Software Support:  
Direct Enablers  
Weight:  
42.7 g, 1.5 oz (including the RJ-45 connector)  
PCMCIA Card Size:  
Length - 3.37" (85 mm)  
Width - 2.13" (54 mm)  
Thickness - 0.197" (5 mm)  
Power Consumption:  
100BASE-TX: 230mA typ., 270 mA max, 3.3 VDC  
10BASE-T : 160Ma typ., 200 mAmax, 3.3 VDC  
Operating Temperature:  
0°-55°C (32°F-131°F)  
Operating Humidity:  
0% - 90% non-condensing  
Storage:  
-20°C-65°C (-4°F–149°F)  
Ethernet Protocols:  
IEEE 802.3U (Fast Ethernet, 100Base-TX)  
IEEE 802.3 (Ethernet, 10Base-T)  
Data Transfer Rate:  
100 or 10 Mbit/sec  
Connector:  
Unshielded RJ-45 female connector.  
 
Product Warranty  
Hypertec Limited warrants the hardware components of the product to be in good working order for the life of the product from the date of  
purchase of the product from Hypertec or an authorised Hypertec dealer. Should the hardware components of the product fail to be in good  
working order at any time, Hypertec will, at its option, repair or replace the product.  
Repair parts and replacement products will be furnished on an exchange basis, and will be either reconditioned or new. All replaced parts will  
become the property of Hypertec.  
This warranty applies only to the original registered end user purchaser of the product and does not include service to repair damage resulting  
from accident, disaster, misuse, abuse or non-Hypertec modification of the product.  
Additional components installed by the dealer or end user are not covered by this warranty. Apart from the above, no warranty is expressed or  
implied, including warranty of merchantability or warranty of fitness for use for a particular purpose.  
The liability of Hypertec is limited to the repair or replacement of the product with a functionally equivalent or better product. Hypertec is not  
liable for any accidental, general, special, exemplary or consequential damages resulting from any product failure, even if Hypertec has been  
advised of the possibility of such damages.  
Hypertec Limited  
Units 1-3 Station Road  
Hungerford, Berkshire RG17 0DY  
Ph: +44 (0)1488 686844  
Fax: +44 (0)1488 686845  
Web:www.hypertec.co.uk  
 

Haier Dishwasher DW12 TFE1 User Manual
Harbor Freight Tools Air Compressor 65549 User Manual
Honeywell Humidifier HE365A User Manual
Honeywell Ventilation Hood D896 User Manual
HP Hewlett Packard Personal Computer DX2200 User Manual
HP Hewlett Packard Webcam HD 5210 User Manual
Hubbell Work Light TMR Series User Manual
Husqvarna Lawn Mower 46S User Manual
Husqvarna Trimmer J123L User Manual
IBM Computer Drive 73P3309 User Manual