OmniProx™ Reader
Installation Instructions
Model Series OP10/20/30/40/45/90
K5336 Rev. 9, 11-Sep-2003
WHAT IS THE Honeywell OmniProx™ READER?
The OmniProx Reader is an RFID proximity card reader to
be installed for use with access control systems.
Check all electrical codes for proper installation.
These installation instructions contain the following
information:
Card Reader Models OP10/20/30/40/45/90 are to be
used with control panels whose power supply is UL
listed Class 2 or equivalent.
U
•
•
•
Mounting Instructions
Connecting the reader to the host
Testing and operation of the reader
L
HOW TO CONNECT THE READER TO THE HOST
The OmniProx Reader is supplied with an 18-inch pigtail,
having a 6-conductor cable. To connect the reader to the
host, perform the following steps:
technical support.
1. If there is a connector on the end of the cable (used
during manufacture for testing purposes), cut it off.
Prepare both the reader cable and host cables by
cutting the cable jacket back 1¼ inches and strip the
wires ½ inch.
2. Splice the reader pigtail wires to the corresponding
host wires and cover each connection (see Figure 2).
HOW TO MOUNT THE READER
Figure 1 shows the front view of the OmniProx. When
mounting models OP10/20/30/40/45, the snap-off cover
must be removed to access the screw holes.
3. If the tamper output is being utilized, connect the
purple wire to the correct input on the host.
Figure 1
®
4. Trim and cover all conductors that are not used.
Figure 2 below shows how you should wire the reader to the
host.
SNAP ON/OFF TOP COVERS:
Hides mounting screws
and protects the reader
The model OP90 uses a security screw on the bottom of the
reader to secure the cover. Remove this security screw
using the supplied tool. Then slide the back plate down
slightly and then lift it up from the bottom. Select the
desired mounting holes and drill them out.
Figure 2
Wiring Notes:
Mount the reader with the appropriate screws (not
supplied) as indicated on the template.
1. The individual wires coming out of the reader are color
coded according to the recommended Wiegand standard.
2. If either 5 or 12 volts are available, use 12 volts for better
performance.
To su r fa ce m ou n t th e r ea d er , p er for m th e follow in g:
1. Determine an appropriate mounting position for the
reader.
2. Peel off the back of the self-stick mounting label
template included with the unit and place at the
desired mounting position. (Additional templates can
be downloaded from www.omniprox.com.)
3. Using the template as a guide, drill two holes (hole size
is indicated on mounting template) for mounting the
reader to the surface.
3. When using a separate power supply for the reader, the
reader, power supply and host must have a common ground.
4. The recommended cable depends on the distance from
the reader to the host. See Table 1 on the next page for
the correct wire gage based upon distance. Larger wire
gauges are acceptable. The wire must be stranded with
an overall shield, either foil or braided. If the tamper is not
being used, 5 conductor cable is required; otherwise 6
conductor cable is required.
5. The cable shield wire on the reader should be attached to
an Earth ground (best) or signal ground connection at the
panel or power supply end of the cable. This configuration
is best for shielding the reader cable from external
interference.
4. Drill a 1/2” (13 mm) hole for the cable. If mounting on
metal, place a grommet or electrical tape around the
edge of the hole.
5. Route the interface cable from the reader and/or power
supply to the host. A lin ea r type power su pply is
r ecom m en d ed .
-1-
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement
for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with
the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide
reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
•
If using an indoor antenna, have a quality outdoor antenna installed.
Reorient the receiving antenna until interference is reduced or eliminated.
Move the radio or television receiver away from the receiver/control.
Move the antenna leads away from any wire runs to the receiver/control.
Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or
master may find the following booklet prepared by the Federal Communications Commission helpful:
"Interference Handbook"
This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
CE CERTIFICATION
DECLARATION OF CONF ORMITY TO COUNCIL DIRECTIVE 89/336/EEC
Standards to which conformity is declared:
ETS 300 683, ETS 300 330 harmonized standard, low power emitters
EN 50130-4:1998 Product family standard: Immunity requirements for components of fire, intruder and social alarm systems
Issued by:
ADEMCO, 165 Eileen Way, Syosset NY 11791
Tel: (516) 921-6704
Date of issue: 4-January-2001
Equipment type: Access Control Proximity Reader
Model numbers
OP10, OP20, OP30, OP40, OP45, and OP90
File No.
BP9666
Ack n ow led gem en ts:
OmniProx is a registered trademark of Honeywell International.
Wiegand is a licensed trademark of HID Corp.
HID is a licensed trademark of HID Corp.
-3-
ADEMCO Limited Warranty
Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165
Eileen Way, Syosset, New York 11791, warrants OmniProx products to be in conformance with its own plans and specifications and to
be free from defects in materials and workmanship under normal use and service for the life of the product. Seller's obligation shall be
limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with
Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation
under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco
factory service. For warranty service, return product transportation prepaid, to Ademco Factory Service, 165 Eileen Way, Syosset, New
York 11791.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE
OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE
LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR
DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any
personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning
or protection. Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery,
fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there
will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING.
However, if Seller is held liable, whether directly or indirectly, for any loss or damage arising under this Limited Warranty or
otherwise, regardless of cause or origin, Seller's maximum liability shall not in any case exceed the purchase price of the product, which
shall be the complete and exclusive remedy against Seller. This warranty replaces any previous warranties and is the only warranty
made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.
165 Eileen Way, Syosset, New York, 11791
Copyright 2003 PITTWAY CORPORATION
ÊK53364Š
K5336 09/11/03
|