Harbor Freight Tools Stud Sensor 45891 User Manual

 
Installation  
1. The safe has four concrete fasteners that  
are inside of the safe when you open  
it. There is also a mounting template  
included with the safe. Place the mounting  
template against the area you will be  
mounting the safe and tape it into place.  
3. To use the concrete fasteners, drill a  
small pilot hole through the template  
to mark the hole placement. Next drill  
four holes in the correct location, using  
a concrete drill bit. Drill the holes the  
same diameter as the fasteners and 2"  
deep. Hammer the fastener in the hole  
with the flat side going into the hole first.  
Use a wood block between the bolt and  
the hammer to protect the threads.  
WARNING! Before drilling or driving  
nails, make sure there are no wires,  
cables or pipes in the path.  
2. To attach the safe to a wood surface,  
hammer a nail (not included) to  
4. Place the safe over the bolts (with  
the nut removed from the bolts)  
mark the hole placement. Drill an  
1/8"diameter pilot hole into each  
mounting hole location. Place the safe  
over the mounting holes and secure  
the safe using four 1/4" diameter  
self-tapping screws (not included).  
and tighten a nut onto each bolt. As  
you tighten the nuts onto the bolts,  
the fasteners will expand inside the  
cement, securing the safe into place.  
Operation  
1. To Open the Safe: Input the numbers  
“159” on the Electronic Key Pad, then  
press either the “A” or “B” Key. Once the  
Green light is on, turn the Knob and pull  
the Door open. Note: The knob must be  
turned within 5 seconds of the Green light  
coming on. If the knob is not turned, the  
entry code will need to be re-entered.  
you can input the new Code (1 to 8  
characters) into the Front Control Panel,  
followed by either the “A” or “B” Key.  
The Safe will beep twice to confirm that  
the Code has been changed. Important:  
If the Safe beeps three times, then  
the Code has not been accepted, and  
you must repeat the steps above.  
2. To Close: Close the Door and turn  
the Knob in the opposite direction.  
The Safe is now locked.  
4. To Change the Batteries: If the Red  
Light and the Green Light are both lit  
at the same time, it is time to change  
the Batteries. Follow the instructions  
for opening the Safe. The Battery  
3. To Change the Code: The Safe comes  
preset with a default code of “159.”  
To change the Code, first follow the  
instructions for opening the Safe. On  
the inside of the Door toward the hinge,  
you will see a small Red Button. Press  
this Button until the Yellow Light on  
the Front Control Panel lights up. Now  
Compartment is located on the inside  
of the Door. Slide the Battery Cover off  
of the Battery Compartment, remove  
used Batteries, and insert four new  
“AA” Batteries. Once you have changed  
the Batteries, be sure to test the Code  
before you close the Door again.  
REV 02d, 04c, 07b  
Item 45891  
For technical questions, please call 1-800-444-3353.  
 
Page 3  
5. Using the Emergency Key:  
c. Turn Knob and pull Door open.  
a. Peel off the Label directly to the  
left of the keypad to reveal the  
Secret Key-Operated Lock.  
d. Replace the Keypad and the  
Label when finished.  
IMPORTANT: NEVER LOCK THE  
EMERGENCY KEYS IN THE SAFE!  
b. Insert Emergency Key into the  
Secret Key-Operated Lock.  
Limited 90 Day Warranty  
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,  
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the  
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,  
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper  
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries  
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of  
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the  
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER  
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with transportation charges  
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.  
If our inspection verifies the defect, we will either repair or replace the product at our election or we may  
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will  
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted  
from causes not within the scope of our warranty, then you must bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
Record Serial Number Here:  
Note: If product has no serial number, record  
Note: Replacement parts are  
month and year of purchase instead.  
not available for this item.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
REV 04a, 07b  
 

Graco Heat Pump 310643u User Manual
Greenheck Fan Ventilation Hood SSSMD 201 User Manual
Greenway Home Products Water Dispenser GWD5960W User Manual
Haier Microwave Oven EB 2080EG User Manual
Hamilton Beach Toaster Toasters User Manual
Harman Kardon Stereo Receiver AVR 8500 User Manual
HP Hewlett Packard Life Jacket 656830 004 User Manual
HP Hewlett Packard Switch 445946 001 User Manual
Hunter Fan Outdoor Ceiling Fan 26405 User Manual
Hyundai Car Video System B70D User Manual