HRFG - ER*A HRFG - SR*A HRFG - SER*A
Halsey Taylor Owners Manual
Refrigerated Marblyte Fountains with Back Panel
Installer
To assure you install this model easily and correctly, PLEASE
READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING
THE INSTALLATION. CHECK YOUR INSTALLATION FOR
COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER
APPLICABLE CODES. After installation, leave these instruc-
tions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES ISACOMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCURAWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICALFEEDBACK
INTOAFOUNTAIN, CREATINGAN ELECTROLYSIS WHICH CAUSESAMETALLIC TASTE ORAN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION ISAVOIDABLE BY USING
THE PROPER MATERIALSAS INDICATED.ANY DRAIN FITTINGS PROVIDED BYTHE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
97716C (Rev. A - 5/02)
HRFG - ER*A HRFG - SR*A HRFG - SER*A
HRFG-SER ROUGH-IN
LEGEND:
A = 3/8" O.D. TUBE WATER OUTLET
B = 3/8" O.D. TUBE WATER INLET
C = 1-1/4" O.D. WASTE TUBE (NOT INCLUDED)
FIG. 2
97716C (Rev. A - 5/02)
PAGE 3
HRFG - ER*A HRFG - SR*A HRFG - SER*A
INSTALLATION INSTRUCTIONS
1. Install remote chiller. Remove front panel of chiller. Remove and discard cardboard inner pack from be
tween compressor and side panel. Slide chiller onto the shelf and position it to the left within the guides
on the shelf.
NOTE: Building construction must allow for adequate air flow on both sides, top, and back of chiller. A
minimum of 4" (102mm) on both sides and top is required. See chiller instructions for additional instructions.
2. Make water supply connections. Attach an unplated copper water inlet line and a service stop (not
provided) to the chiller. Inlet port is marked on the chiller (3/8" O.D. copper tube). Bend the copper tube
(provided) at an appropriate length from chiller to opening in frame. Install a 3/8" O.D. tube tee fitting (pro
vided) on the marked chiller outlet port. Turn on the water supply and flush the line thoroughly.
3. Hang the upper panel on the mounting frame hanger. Align holes in the panel with the holes in the
mounting frame. Be sure that panel is engaged with hanger at top of frame before releasing it.
4. Install fountain. Remove access cover plate on underside of fountains and save the screws. Mount the
fountains to the upper panel and the wall frame with (4) 5/16" x 1-1/4" (32mm) long bolts, washers, and nuts.
Tighten securely, but do not overtighten. Over tightening will crack the Marblyte Fountain.
NOTE: The short fountain should be mounted to the upper left hand side of the panel.
5. Remove elbow from end of p-trap and attach it to drain tube. Re-attach elbow to p-trap and cut waste
tube to required length using plumbing hardware and trap as a guide.
6. Make connection between remote chiller outlet tube and fountain strainer. Insert the water inlet line
into inlet side of strainer by pushing it in until it reaches a positive stop, approximately 3/4" (19mm). Turn on
water supply and check for leaks. Newly installed water supply line should be insulated after leak check is
completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE O-RINGS
MAY RESULT.
7. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
8. Make electrical connections to the chiller. See chiller instructions.
9. Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, remove items 5 & 13 (See Figure 6, Page 6) by loosening set screw (item 10) and adjust
the screw on regulator (item 9). Clockwise adjustment will raise stream height and counter-clockwise
adjustment will lower stream height. For best adjustment stream height should be approximately 1-1/2"
(38mm) above the bubbler guard (See Figure 5, Page 5).
10. Mount lower panel. Loosen the (2) #10-24 x 5/8" (16mm) screws at frame bottom lip. Slide upper tongue
of lower panel under lower edge of already installed upper panel. Tighten previously loosened screws
securely.
11. Replace bottom access panel to fountain basin using screws provided. Tighten securely.
Care and Maintenance of Halsey Taylor Marblyte Fountains
Marblyte provides an exremely durable, nonporous surface which resists staining. Care is very
simple. Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam
cleaner, is all that is normally needed to give many years of trouble free service. Cleaners left
standing on the fountain surface can dull the surface finish. Be certain to rinse all cleaning agents
completely and polish with a soft cloth.
Harsh abrasive cleaners are not required and should not be used.
Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove
simple scratches and stains. Cigarette burns can normally be removed without noticeable effect.
Deeper scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a
green Scotchbrite pad.
To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or
like products will keep the finish looking like new.
97716C (Rev. A - 5/02)
PAGE 4
HRFG - ER*A HRFG - SR*A HRFG - SER*A
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
1/4" O.D. TUBE
WATER INLET
TO COOLER
BUILDING WATER INLET
NOTE: WATER FLOW
DIRECTION
SERVICE STOP
(NOT FURNISHED)
FIG. 3
OPERATION OF QUICK CONNECT FITTINGS
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
SIMPLY PUSH IN
TUBE TOATTACH
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 4
FIG. 5
PAGE 5
97716C (Rev. A - 5/02)
HRFG - ER*A HRFG - SR*A HRFG - SER*A
9
7
2
6
13
5
10
BASIN
26
16
FIG. 6
TOP VIEW
23
8
SEE FI
24
25
SEE FIG. 6
19
FIG. 7
97716C (Rev. A - 5/02)
PAGE 6
HRFG - ER*A HRFG - SR*A HRFG - SER*A
FIG. 8
FIG. 9
PAGE 7
97716C (Rev. A - 5/02)
HRFG - ER*A HRFG - SR*A HRFG - SER*A
PARTS LIST
ITEMNO.
PARTNO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Drain
Retaining Nut
Strainer
Tailpipe Ferrule
Push Button
Push Button Sleeve
Regulator Holder
Bubbler
Regulator
Setscrew #6-32 x .31"
Scr, #10-24 x 1/2 PH TR HD-Z
Strainer
Push Button - Extension
Bottom Cover Plate-Short
Bottom Cover Plate-Extended
Back Panel HRF-SER
Back Panel HRF-ER
Back Panel HRF-SR
Hex Nut
Insert - Threaded
Bubbler Locknut
Lower Panel HRF-SER
Lower Panel HRF-ER
Union - 3/8" x 1/4"
Union - 3/8"
LK464
15005C
40038C
40619C
45662C
45738C
50986C
51544C
61313C
70022C
112627543890
55996C
56087C
27201C
27658C
26839C
26837C
26835C
40045C
75554C
70012C
27026C
26833C
70745C
70870C
70852C
55969C
56053C
56025C
56056C
100322740560
66399C
45736C
15
16
17
18
19
20
21
22
23
Tee - 3/8"
Fountain-Galaxy Gray(HRFG-S)
Fountain-Galaxy Gray(HRFG-E)
Fountain-Black(HRFG-S)
Fountain-Black(HRFG-E)
Gasket - Black
24
25
26
Tube Assy - Reg. to Bubbler
Nut - Regulator Mounting
TROUBLE SHOOTING & MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be
removed from the orifice with a small round file not over 1/8" diameter or small diameter wire.
CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is free of material deposits, regulate flow as instructions on page 4(Step 9). If replace-
ment is necessary, see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring
water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the
tubing.(see Fig.4, Page 5) To insert tubing, push tube straight into fitting until it reaches a positive stop,
approximately 3/4".
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
97716C (Rev. A - 5/02)
PAGE 8
|