Environmental-friendly Double
Drive Washing Machine
User's manual
This manual is for
HWM70-0588
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Packing list
Water inlet valve
Water absorption gasket
One
One
User's manual
Warranty card
Inside the document bag
Inside the document bag
Top lid component
Inner cover
Detergent box
Control panel seat
Outer tub cover
Balance ring
Power cord
Screw cover
Hook
Components of the water inlet
hose
Cabinet handle
Drain hose
Attach block
One
Inside the accessory bag
Inner tub
Lint filter
Pulsator
Front control board
Cabinet
Front door
Drain
protective lid
Bottom plate
Between the upper cushion of the washing
machine package and the upper seal of the
package carton
One
Liquid blenching filler
Adjustable leg
Back cover
Drain protective lid
Base frame
Fixed leg (3 pieces)
Inner cover
component
One
Inside the accessory bag
Meaning and description of the symbols
Automatic washing machine
One
Warning sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Specification table
Water level/Water
quantity (about)
Forbidden sign
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in damage of
the machine or influence the personal safety of the users.
Water Injection pressure
0.03MPa
0.78MPa
~
Standard washing /
spinning capacity
7.0kg/7.0kg
1
Trouble-shooting answer to question
Safety precautions
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes.
Please confirm again before sending it to repair. Do not repair it by yourself.
The washing machine must be positioned
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Phenomena
The reason
How to settle
so that the plug is accessible. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
c l e a n i n g t h e m a c h i n e . D o n o t p l u g
or pull the power plug with wet hand.
Close the top lid.
The digitron displays E0.
The top lid is opened during reserve procedure.
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
It stops running in midway. The digitron
displays E2.
The top lid is not closed.
Close the top lid.
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by
the technicians of our special shop or our customer care agent.
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Are the laundries put slantingly?
Is the machine slanting?
Reorder the laundries. Close the top lid.
Th machine will start running after 10
seconds of being placed horizontally.
Open the water tap. Push the start/Pause
button once.
Clean the water inlet valve then push
the Start/Pause button once.
Push the Start/Pause button once.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water filling does not work, or is
slow. After about 15 minutes later,
the digital displays E4.
Please contact the after-sales
service department.
The digitron displays E6.
The digitron displays E7.
The water level sensor is bad.
The communication is bad.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
.
Please contact the after-sales service
department.
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
The ventilation
holes at the bottom
Not wash
The machine does
not act
Carpet
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Not spin
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
There's abnormal sound
inside the machine
Is the screw of the jointer of water
inlet hose loose or awry?
Fasten the screw of the jointer properly.
The water tap leaks
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure is paused.
The cloth sensor is checking the cloth, it willadd waterafter 48 seconds.
The program is setting the drain time. Some time is needed
before it starts spinning.
Push the PROGRAM button to select SPIN,
but it doesn't work.
The pulsator pauses during water inlet
in wash and rinse.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
2
Disposal after washing
Safety precautions
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Lint filter:
1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle: Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it
tight .
trol
Pe
Benzene
6.Make sure the lint filter well installed, or it can
influence your use.
The back cover of lint filter
Up
Up
Dismantle
Dismantle
Dismantle
Install
Install
Install
Down
Keep the machine away from direct sunlight and
heat source like the heater.
The handicapped or children without care shall not use
the machine.
The front cover of lint filter
Figure 2
Down
Figure 1
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Please clean it with brush every two months.
Wipe it with neutral detergent.
Do not wipe it with thinner, petrol, alcohol etc.
r
e
Petrol
Alcohol
Thinn
Please keep the lint filter in good condition,
and install it to proper position during
washing. If the lint filter is lost or
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Install
Dismantle
damaged, please contact the customer
care agent of our company.
.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
To change the direction of drain pipe, please contact the customer care agent of our company.
4.Hang up the power cord and drain hose.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 24 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
3 Push "SOAK" "WASH/SPEED" "RINSE" "SPIN/SPEED"
button to select suitable procedure program
Install the Inner cover component
Attention
Before initial use of the machine, assemble the inner cover as described below:
1.Open the top lid of the washing machine.
2.Put the inner cover component on the outer tub cover, aiming
the inner cover shaft to the installation hole of the
corresponding outer tub cover shaft groove.
Even there's no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
The soak procedure can work in cooperation with automatic programs like normal, comforter
There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing,
and can not make setting in other cases.
Outer tub cover
Outer tub cover shaft groove
Inner cover shaft
Inner cover
3.Firstly insert the inner cover shaft of one side into the
corresponding outer tub cover shaft groove, then push
the another inner cover shaft into the corresponding
outer tub cover shaft groove. Please install to designated
position to guarantee there are no dropping or abnormal
sound in opening and closing of the inner cover, and the
operation shall be smooth. Do not dismount the inner cover
component after washing.
If the water pressureis too low,in order to washthe cloth cleanly,the machine will change
from " SAVING WATER"to "storing water "automatically.
Damping cushion
4 Push the " WATER LEVEL "button, select
suitable water level
Push
Section I enlarging
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "START/PAUSE"
button, then push the "WATER LEVEL" button to set the water level.
Install the bottom plate
5 Push the "AIR DRY"button to select suitable dry time.
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
I
Back
6 Push the "RESERVE" button to select suitable reserve wash
program
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the " RESERVE " button to
set the reserve wash program. Refer to reserve button in Page 11 for selection.
Front
Bottom plate
Soft items
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Section I enlarging
Confirm the operation of reserve program
When the "RESERVE" function is activated, the indicator light of the program you
have set will be off. The "reserve (hour)" and "time remain" indicator lights will
be on. During reserve procedure, push the "RESERVE" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
Adjust the Installation position
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground
will result in unstable running or stoppage of the machine. Please adjust it with following methods:
need to switch off the power and make new selection.
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
7 Push the "START/PAUSE" button
6 Finish washing
Adjust the adjustable leg:
5 Close the top lid
1 .To twist the adjustable leg, please first lift up the
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
After finishing wash it'll
alarm and switch off power
automatically
As the top lid opened, the washer will automatically
given alarm and stop running, exclusively during
draining.
the adjustable nut
Fasten
Loosen
2 . After adjustment, fasten the nut.
the adjustable feet
High
Low
How to change the direction of the drain hose
1.Dismantle the rear cover of the washing machine.
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
2.Put down the drain hose Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet then nip the drain fixing clamp to make
it deviated from the clip the other hand is used to put
down the drain bushing as indicated in Figure 2 3.
b
Steps of using the operation buttons and description
Wash/spin
speed
Program
REMAIN
of the steps
SOAK
WASH
RINSE
SPIN
••
•
•
•
•
•
•
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
Normal
Air dry
120
Standard
4
Woollen
Carpet
3
Quick wash
Posthaste
60
•
2
drain outlet protecting
cover
Saving water
Jean
•
•
Overflow
RESERVE
Drain hose
SPIN
PROGRAM
RESERVE
Figure 5
Figure 4
SPEED
LOCK
Drain hose support
Cabinet
Inner
Drain bushing
Figure 2
Drain bushing
7
Figure 1
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Outer
4
2
Push
Drain bushing
Take
down
Drain hose fixing
clamp
Figure 6
Push
Figure 3
1.Push "POWER" button to switch on the power
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
2.Push "PROGRAM"button to select suitable full-auto program
After the power is switched on, "Normal" is automatically set. To select other full-auto program, please push
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 11.
E.g. Set to "Speedily"program for small quantity of laundries with light soil.
Usage the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.
Notes:
4.If extra drain hose is needed, please make
10cm, or the drainage will not be smooth, and
separate purchase. The inner diameter of the
cost such long time that the machine may stop
extra hose shall not less than 30mm, and the
The washing machine has a Woollen program and a Carpet program, intended for high-grade fabrics such
as cashmere and carpet. First, make sure the laundry can be washed with water or not. If not, do not use the
washing machine to wash the laundry. If yes, select the washing cycle recommended by the fabric man
ufacturer. The Woollen program can be used to wash fine clothes such as cashmere sweater, linen blouse,
woolen pants; the Carpet program can be used to wash carpets or heavy fabrics indicated as hand wash or
machine wash compatible. For clothes with local stains, such as sticky stains at collar or cuff, lay the clothes
upon a towel and spread neutral detergent (for washing machine) on the stains. Use a soft brush to pat at the
clothes gently before putting the clothes into the machine. Do not rub the clothes hard.
Before washing, please fold up the laundry as needed, then put the laundry into the inner tub, flat and neat.
These fabrics are not washable:
at mid way.
length shall not exceed 1.5m.
2.Do not step on or press the drain hose.
>
30mm
<10cm
<1.5m
1. Fabrics that deform when soaked in water;
2.Fabrics that shrink, discolor or go through other exterior changes when soaked in water;
3. If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
5.If the extra hose is too long, cut it either at A
or at B.
3.Fabrics that lose original texture when soaked in water;
4.Fabrics that discolor when soaked in water;
5.Fabrics that have pilling or pressed pile when soaked in water;
6.Fabrics that have damage when soaked in water.
Upon completion of washing, iron the laundry with a steam iron.
When shrinkage occurs
Hold the steam iron above
Stretch the laundryto its original
the laundry and do not touch
size and locate it with pins. Use
the laundry. Reshape the
a steam iron to dry the laundry
completely. Donot touch the
laundry. (Asillustrated in Fig 2)
laundry. (As illustrated
in Fig 1)
Pin
Figure 2
Figure 1
5
12
Install the water inlet hose
Confirm the water faucet
Water faucet,suitable
"Air dry"button
.
Push the button to toselect the different air dry time(60 120 180
Reserve, remain time digitron
).
Minutes .To select60minutes can dry theinner or outer tub.
It displays "--" during detecting.
Water faucet,not suitable
To select120 or 180minutes candry clothes.(both lighter ison
indicate the 180minutes program).The weight of the clothes is
1.5kg at most.
It displays remained reserve time (hour).
It displays total remained time (min). If the total time
exceeds 99 minutes, it uses "A" on tens digit to
represent100 minutes, and uses "b" to represent 110
minutes. E.g. "A3" represents 103 minutes.
It displays abnormal symbol in abnormal situation.
(See to Page15)
Outlet end surface
>10mm
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
"POWER" button
Push the "POWER" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "POWER" button to switch on the power. If
the "START/PAUSE" button is not pushed, the machine
will switch off the power automatically after 5 minutes.
Remain
Program
Standard
••
•
•
•
•
•
•
Normal
Quick
Connection between the water inlet hose jointer and the water faucet
Woollen
Carpet
Saving water
Air dry
120
Posthaste
•
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
60
Jean
•
•
Reserve
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
dry
Air
Program
Reserve
LOCK
water inlet hose jointer
Screw
Slider
Sign plate
Screw knife
Bushing
Figure 3
"PROGRAM"button
Lock level
"WATER LEVEL"button
"RESERVE" button
Following full-auto program is available
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among
4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push the
start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .If wet laundries are put
in, it may display water level 10. You must set suitable water level
by yourself.
The digitron displays the time
remained (in minute) before
the washing is finished.
water inlet hose
Program
Application
Figure 2
Figure 1
Normal Washing for normal laundries
Push down the reserve
Quick
Quick washing for normal laundries
Washing for light-soil a few laundries
Washing for big and thick laundries
button. The reserve indicator
light is on the digitron displays
the reserve time of finishing
washing (in hour).The time
remain indicator light is on,
indicating that the reserve
function is running.
3.Fasten the four screws evenly. See to Figure 4.
Posthaste
Jean
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Standard
Standard saving washing for normal laundries
If Posthaste program is selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform
washing while filling water. When water level 3 is reached, it will
change to normal washing.
Woollen Washing for the woollen laundries,
under 2.5kg
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Push the reserve button can
display the reserve state.
Carpet Washing for carpet and wearing bigger
Laundries, under 3.0kg
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
Saving water
Saving washing for light-soil laundries
About 4mm before twisting
About less than 2mm after twisting
The water level decided may be different from actual value because
of the different moisture level of the laundries.
Screw nut
Figure 5
Figure 4
Figure 6
4 Use the operation button
Description of operation button
Connection between the water inlet hose and the washer
a
Indicator mode and meaning
1.Do not take off the water absorption cushion. Please check if the
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
please contact our after-sale department immediately.
Flashing, indicating the running program
On, indicating the program about to run or the selection mode
2 .Put the nut of the water inlet hose on the valve jointer.
3 .Fasten the nut. Swing it gently to confirm if it's suitable.
jointer of the
water inlet valve
water absorption
cushion.
"START/PAUSE" button
After the poweris switched on, press it to
start the machine
During working, push it to pause.
During pause, push this button to restart
and go on working
Wash/spin
speed
Wash
Spin
Rinse
Connection between the jointer of the water inlet hose and the water inlet hose
•
•
Soak
1.Push down the slider. Insert the water inlet hose into the jointer.
the jointer of the
water inlet hose
Overflow
Locking level
Slider
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
SPIN
SPEED
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
"SPIN/SPEED " button
Press the Spin/Speed button to
select a spin procedure.
The button can beused to select
the desired spin time(1,3,5,7
minutes )from the Normal program
or the Jean program.
The button is unavailablefrom the
Saving,quickwash,posthaste Standard,
Carpet, Woollen programs.
"SOAK "button
"WASH/SPEED " button
"RINSE" button
Press the Soak buttonto select a soak
procedure.
Press the Washbutton to select a
wash procedure.
The button can beused to select
the desired wash time(0,6,9,12,15
minutes) from the Normal and
Jean program.
The button is unavailable from the
Saving,quickwash,posthaste Standard,
Carpet, Woollen programs.
For the Normal Jean program,
press the button for2 seconds to
start wash speed selection.The
speed from 1 to4 is available for
selection. The default value is 2.
Press the Rinse buttonto select a
rinse procedure.
The button can beused to select the
desired soak time( 10,20 minutes)
from the Normal andComforter
programs.
The button can beused to select
the desired number ofrinse cycles,
(0, 1, 2 ,3 times )from theNormal
program or the Jeanprogram.
While the "Overflow" digitron is
lighting,the program of theoverflow
rinse has been selected.
The button is unavailablefrom the
Saving,Speedily, Standard,Woollen,
Carpet and Delicate programs.
For the Normal orJean program,
press the button for2 seconds to
start spin speed selection. The
speed from 1 to4 is available for
selection. The defaultvalue is 2.
The button is unavailable from the
Saving,quickwash,posthaste Standard,
Carpet, Woollen programs.
Dismantle the water inlet hose
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
Locking level
If the machine is used frequently, the jointer of the water inlet hose can be
on the faucet to prevent damaging the fixing screw.
Slider
kept
1 Preparation before washing
2 Put in the laundries
Preparation before washing
1.Connect the water inlet hose.
The capacity of washing of the machine refer to the largest weight of the
standard laundries under dry condition that can be washed in one
time. Laundries quantity in one washing cycle shall be lower than
the standard capacity. The largest capacity of this machine is 7.0 kg.
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be turned
round in washing for one time washing.
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
3 Usage of the detergent
Control panel seat
Washing powder inlet
Liquid detergent inlet
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Detergent box
Pay attention to followings before washing the laundries
How to use softener
How to use washing powder
See to the manual of softener for the usage and dosage.
When adding softener into the softener inlet of washing
powder box, note that it shall not exceed the lower side
of the cap.
Do not leave the softener for long period after adding it
into the box. Otherwise it may be solidified and block the inlet.
As the softener is easy to solidify, please clean the box
frequently.(You shall clean it each time you use reserve
function).
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Confirm if there's
special requirement
for the laundries.
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
1.Add some water(select " 1 " water level).
2.Add washing powder. Run for about 30s to fully dissolve
laundries.
Before use softener, you must select to sterilize function
Powder. Then push the"START/PAUSE" button.
the
3.Put in laundries. Select suitable water level. Push the
Button again.
"START/PAUSE"
How to use whitener
Quick dissolving of washing powder:
1.Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it completely.
When choosing the " No detergent" program, the usage of
softener or whitener is same as using detergent.
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
If you select "Speedily" program, it is suggested to use
liquid detergent instead of washing powder to guarantee
the washing effect.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g. For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into
mesh bag for washing.
Add water to stipulated level. Dilute the whitener with container,
and then pour it into the liquid whitener inlet slowly.
Laundries with color or pattern is not colorfast, thus not applicable.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
It is not recommended to use rich-foam washing powder.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
|