MODEL H8175
PROFESSIONAL
PNEUMATIC GLUE GUN
INSTRUCTION SHEET
Case
EYE/SKIN BURN HAZARD!
Wear safety glasses and
protective clothing when
using this tool!
INJURY HAZARD!
Air
Regulator
Always disconnect tool from
air to prevent unexpected
operation during service!
Gun
DO NOT EXCEED 100 PSI!
Personal injury could
occur.
Screwdriver
Extra Nozzles
ELECTRICITY HAZARD!
Electrocution or fire could
result if this tool is not
properly grounded. Do not
remove the ground pin.
Figure 1. Model H8175.
1
4. Insert a ⁄2" diameter glue stick into the back
of the gun.
5. Once the gun has fully heated, slowly squeeze
the trigger until the melted material begins to
flow from the nozzle.
Specifications
Air Regulator Inlet Size ............................1⁄4" NPT
Operating Temperature...................284°F–428°F
Maximum Temperature ...............................446°F
Operating Air Pressure.............................. 90 PSI
Note: When hot, rest the gun with the tip fac-
ing down, as shown in Figure 1, to prevent
melted glue from escaping the chamber and
increasing the risk of fire or personal injury.
Glue Stick Diameter ......................................... 1⁄2
Cord Length.................................................... 2 ft.
Weight ...........................................................3 lbs
"
6. After the gluing operation is complete, allow
the glue gun to fully cool before storing it.
Glue sticks may remain in the glue gun when
it is not in use and be re-melted when the
glue gun is used again.
Operation
1. Connect the glue gun to the air regulator and
connect the air regulator to the air supply.
2. Plug the glue gun into a grounded outlet and
turn it ON with the power switch located at the
base of the glue gun.
Note: Never pull the glue stick out through
the back of the gun or it may damage the
feed mechanism. Cut off the extra portion of
the glue and feed the remainder through the
glue gun.
3. Allow the gun to heat up for approximately 3–5
minutes.
COPyRIGHT © MAy, 2008 By GRIzzLy INDuSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROvAL OF GRIZZLY INDUSTRIAL, INC.
#JM10780 PRINTED IN TAIWAN
Changing Nozzles
Temperature Adjustment
The Model H8175 glue gun comes with three noz-
zles for different gluing applications and output
amounts. The all metal nozzle is for heavy duty
and high output applications. The long tip of the
silicon nozzle is ideal for bonding items with mini-
mal accessibility. The silicon coating reduces the
risk of accidental burns. After extensive use, the
nozzle may begin to drip excessively or produce
an intermittent flow. Nozzles should be changed
regularly to ensure an even flow and reduce the
risk of a possible fire hazard.
The Model H8175 glue gun temperature can be
adjusted from 284°F–428°F.
To adjust the glue gun temperature:
1. using the screwdriver, adjust the tempera-
ture control located at the top of the glue gun
(Figure 7).
Temperature
Control
To change the glue gun nozzle:
1. Heat the gun for approximately 1 minute to
soften the glue.
2. Put on a pair of gloves, and use a wrench to
remove the nozzle.
Screwdriver
Storage
3. Flush the remaining glue through the gun to
clean the chamber.
Figure 7. Temperature control.
Note: Never pull the glue stick out through
the back of the gun or it may damage the
feed mechanism.
Note: The screwdriver can be stored in the
base of the glue gun for quick future use.
4. Thread the new nozzle onto the gun until
snug–do not overtighten.
NOTICE
Some materials are heat sensitive and may
become damaged either by the heated noz-
zle or the glue. Test the temperature setting
on a scrap piece of material.
Fluid Output Adjustment
The amount of glue being used can be preset by
using the fluid control knob, as shown in Figure
6. Lock the adjustment by screwing the adjust nut
towards the back of the fluid control knob until it is
flush with the gun body.
If you need help with your new pneumatic tool, call
our Tech Support at: (570) 546-9663.
Fluid Control
Knob
Adjust Nut
Figure 6. Fluid control knob.
-3-
Model H8175 Professional Pnuematic Glue Gun
H8175 Parts Breakdown and List
(
&
)
',
'-
&-
(&
'%
'
'&
''
'(
((
('
'.
*
')
+
(%
'*
&)
()
-
,
'
&.
'+
(*
&%
.
&(
&%
(.
&+
&&
&,
&'
(+
&*
(-
(,
REF PART #
DESCRIPTION
REF PART #
PH8175021 CABLE TIE
PH8175022 SCREW
DESCRIPTION
1
PH8175001 GUN BODY
PH8175002 SPACER
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
2
3
PH8175003 TEMPERATURE CONTROL
PH8175004 GRIZZLY NAME PLATE
PH8175005 RUBBER INLET RING
PH8175006 FLUID CONTROL KNOB
PH8175007 FLUID ADJUST NUT
PH8175008 SPECIAL NUT
PH8175023 WASHER
4
PH8175024 HEATING ASSEMBLY
5
PH8175025 POWER SWITCH ASSEMBLY
PH8175026 POWER CORD
6
7
PH8175027 FUSE ASSEMBLY
PH8175028 TEMPERATURE ASSEMBLY
PH8175029 GROUND WIRE ASSEMBLY
PH8175030 INLET TUBE ASSEMBLY
PH8175031 WIRE
8
9
PH8175009 CORD BRACKET
10
11
12
13
14
15
16
17
18
19
20
PHTEK9M
TAP SCREW M3 X 15
PH8175011 TRIGGER
PH8175012 TORSION SPRING
PH8175013 FEEDER ASSEMBLY
PH8175014 AIR CYLINDER ASSEMBLY
PH8175015 AIR VALVE
PH8175032 NOZZLE SPACER
PH8175033 SILICON NOZZLE
PH8175034 METAL NOZZLE
PH8175035 CASE
PH8175016 AIR REGULATOR ASSEMBLY
PH8175017 SCREWDRIVER
PH8175018 CHAMBER ASSEMBLY
PH8175019 WIRE
PH8175036 FEMALE BARBED HOSE FITTING 1/4" NPT
PH8175037 AIR REGULATOR HOSE
PH8175038 AIR REGULATOR HOSE QUICK CONNECT
PH8175039 MALE AIR FITTING 1/8" NPT
PH8175020 WIRE NUT
-4-
Model H8175 Professional Pnuematic Glue Gun
|